DASH Mining

A detailed tutorial to mine DASH with AntMiner (D3)

DASH are mined using a cryptographic algorithm called X11, which consists of 11 different hashes (blake, bmw, grs, skein, jh, keccak, luffa, cubehash, shavite, simd512, echo).

Using D3 as an example, we will demonstrate the operational process of mining DASH with our AntMiner.

Video tutorial:

https://support.bitmain.com/hc/en-us/articles/360008379974-How-to-set-up-a-new-D3

1.   ANTPOOL account registration and configuration

For details, please refer to "FAQ——Account Registration"

2.    Install the miner, connect miner with network cable and turn on the power (the voltage needs to be around 210v-230v; 1M bandwidth can carry about 200 miners; the local network should be stable)

3. Retrieve miner's IP

1)   To download miner IP reporter software, please click on the link:

https://service.bitmain.com/support/download?product=IP-reporter

2)   Download “IP-reporter”. Requirement: Miner must be connected with a network cable and powered on; your computer and your miner needs to be in the same IP range (For example, miner’s IP is 192.168.0.2; computer’s IP is 192.168.0.67 is considered being in the same IP range). For more information please refer to https://support.bitmain.com/hc/en-us/articles/360009263654-Where-and-how-to-use-IP-Reporter

4. Set static IP for miners

1) If you own more than three miners, we would like to recommend that you set static IP for your miners to better manage them.

2) Static IP setting manual please refer to below link:

https://support.bitmain.com/hc/en-us/articles/222647908-How-to-set-a-static-IP-address- 

5.   Batch configure miners’ IP

To batch configure and manage your miners, you can download “APMinerTool V1.0.8”.

 6.   Log in to miner backend

1)  After you have retrieve your miner IP address using IP reporter tool, open the browser on your computer (Chrome or Firefox is preferred, and the computer needs to be in the same IP range), enter the found IP into the address bar of the browser, and proceed to login using root for both the username and password:

7.   Connect to ANTPOOL and set up miners

1)    stratum server address: (can be found in the bottom right corner of ANTPOOL DASH page)

①stratum-dash.antpool.com:6099

②stratum-dash.antpool.com:443

③stratum-dash.antpool.com:25

2)    Set up miners and connect to ANTPOOL (worker name is sub-account name + suffix, for example, sub-account: always; the first miner is named: always.01, the second miner: always.02... and so on)

3)   Fill in the three stratum server addresses to miner backend (recommended to enter only one miner name for the three server addresses, password can be 123). Click “Save & Apply” to run the miner.

4)    Keep miner running for about 10 minutes; check miner hash rate, temperature and other parameters under miner status from miner backstage

(Note: As long as one of the three stratum server addresses is live, the connection would be ok. If the primary server is offline, miner will automatically switch to the second address and this does not impact your earnings.)

Parameters under Miner Status:

A: Operation time          

B: Miner hash rate

C: Pool connection status, “Alive” means connected

D: Error rate, normally lower than 0.03%

E: Number of Hash boards     

F: Number of chips detected in the chain

G: ASIC frequency setting

H: Hash rate of each hash board  

I: Hash board temperature  

J: ASIC temperature

K: ASIC status, “O” indicates OK; “X” indicates error; “-” indicates dead  

L: Fan speed

5)    Keep miner running for about 10 minutes, check hashrate in ANTPOOL 

8.   Earnings and payment

1)   ANTPOOL provides daily payouts. Once your earning reaches the minimum payment amount, payouts will be sent to your wallet automatically. (DASH default minimum payout amount is 0.001. This amount can be managed by you.)

2) Payment will be sent to the wallet you set up on ANTPOOL. You can check the payment in your wallet or view your payment history under “Dashboard”– “Payment History” on ANTPOOL. (Paying: payment is being process; Paid: payment completed, tokens sent to your wallet)

(If you did not set up a wallet address, your earnings will be kept in your account balance.)

Note：Please make sure to use a valid wallet address for mining. ANTPOOL will not be responsible for any loss of earnings caused by wrong wallet configuration.

9.  Now that we have gone through all the processes of account registration, miner configuration, and connecting to ANTPOOL, we hope you have a great time mining with us!